Filtern
Dokumenttyp
Schlagworte
- carbon nanofibers, platinum electrodeposition, ele ctrochemical surface area (1)
- Cavitation; Corrosion; Laser remelting; Self-fluxing alloys; Stellite 6 (1)
- Erneuerbare Energien (1)
- Hydraulic compression, Carbon Nano Fibers, PEM Fuel Cells, Catalyst utilization (1)
- Hydrogen evolution reaction (1)
- Kohlenstoff-Nanoröhre (1)
- PEM fuel cell electrocatalysts, Carbon nanofibers, Oxygen plasma activation, Pulsed electroplating. (1)
- PEM water electrolysis (1)
- Polymer-Elektrolytmembran-Brennstoffzelle (1)
- PtCoMn (1)
Institut
Based on the fact that titanium and titanium alloys have poor fretting fatigue resistance and poor tribological properties, it is necessary to apply some surface engineering methods in order to increase the exploitation characteristics of these materials. One may either implement some surface treatment technologies or even deposit overlay coatings by thermal spraying.
The present study is focused on the achieved properties of the ceramic coatings (Al2O3 + 13 wt.% TiO2) deposited onto a titanium substrate using high velocity oxygen fuel (HVOF) and plasma spraying (APS) respectively.
The effect of the deposition method on the microstructure, phase constituents, and mechanical properties of the ceramic coatings was investigated by means of scanning electron microscopy (SEM), X-ray diffraction technique (XRD) and nanoindentation tests. The sliding wear performances of the Al2O3–TiO2 coatings were tested using a pin on disk wear tester.
Since the 1980’s, against the backdrop of global warming and the decline of conventional energy resources, low emission and renewable energy systems have gotten into the focus of politics as well as research and development. In order to decrease the emission of greenhouse gases Germany intents to generate 80% of its electrical energy from renewable and low emission sources by 2050. For low emission electricity generation hydrogen operated fuel cells are a potential solution. However, although fuel cell technology has been well known since the 19th century cost effective materials are needed to achieve a breakthrough in the market.
Proton Exchange Membrane Fuel Cells with Carbon Nanotubes as Electrode Material
At the Westphalian Energy Institute of the Wesphalian University of Applied Sciences one main focus is on the research of proton exchange membrane fuel cells (PEMFC). PEMFC membrane electrode assemblies (MEA) consist of a polymer membrane with electrolytic properties covered on both sides by a catalyst layer (CL) as well as a porous and electrical conductive gas diffusion layer (GDL).
For PEMFC carbon nanotubes (CNT) have ideal properties as electrode material concerning electrical conductivity, oxidation resistance and media transport. CNTs are suitable for the use as catalyst support material within the CL due to their large surface in comparison to conventional carbon supports. Furthermore, oxygen plasma treated CNTs show electrochemical activity referred to hydrogen adsorption and desorption, which has been shown by cyclic voltammetry in 0.5 M sulfuric acid solution. According to the PEMFCs anode a GDL coated with oxygen plasma activated CNTs has promising properties to significantly reduce catalyst content (e.g. platinum) of the anodic CL.
The membrane electrode assemblies (MEA) for polymer electrolyte membrane fuel cells (PEMFC) developed at the Westphalian Energy Institute are based on oxygen plasma activated carbon nanotubes (CNT) doped with platinum particles. For electrode preparation an ink is used containing the activated CNTs as well as hydrophobic and hydrophilic material in solved form. After this ink is sprayed onto a graphitic substrate platinum particles are deposited by pulse plating method, where the plasma activation enhances CNT dispersibility as well as platinum deposition. This materials mixture is structured in nanoscale with the aim to increase the catalyst particles’ specific surface. For low reactance at operation, homogeneous compression of the MEA’s layers is necessary within a PEMFC. A novel stack architecture for electrochemical cells, especially PEMFC as well as PEM electrolysers, has been developed in order to achieve ideal cell operation conditions. Single cells of such a stack are inserted into flexible slots that are surrounded by a hydraulic medium which is pressurised during operation in order to achieve an even compression and cooling of the stack’s cells. With this stack design it has been possible to construct a test facility for simultaneous characterisation of several MEA samples. As compression and temperature conditions of every single sample are the same, the effects of e.g. different electrode configurations can be investigated with the novel test system.